Please use this identifier to cite or link to this item: https://idr.l2.nitk.ac.in/jspui/handle/123456789/14565
Title: Experimental Investigations on Friction Stir Welded Joint of Dissimilar Aluminium Alloys
Authors: Anilkumar, K. S.
Supervisors: Murigendrappa, S. M.
Kumar, Hemantha
Keywords: Department of Mechanical Engineering;Friction stir welding;Bottom-up approach;Optimization technique;Dissimilar aluminium alloys;Composites;Nano silicon carbide particles;Microstructure;Mechanical properties
Issue Date: 2019
Publisher: National Institute of Technology Karnataka, Surathkal
Abstract: Friction stir welding (FSW) is solid-state joining process for producing similar or dissimilar joints of plates. Joining process carried out by means of a non-consumable rotating tool passed along the joining edges of plates, after developing sufficient amount of heat. The joints may prone to have defects such as pin-hole, cracks, tunnel defects, worm-hole defects, sharp boundary defects, etc. lead to influence the mechanical properties and microstructures. Main motivation of the present study is to produce defect-free joints and, improve the mechanical properties and microstructures of the friction stir welded dissimilar aluminium alloys joint. To achieve these, it is necessary to choose the optimum FSW parameters such as tool plunge depth, tool rotational speed, tool traverse speed, tool tilt angle, etc. The present study focuses on selection of an optimum FSW parameters using a bottom-up optimization experimental approach for joining dissimilar aluminium alloys. Further focuses on the combined effect of tool probe offset and the tool traverse speed on the properties of welded joint. Study also focuses on the fabrication of metal matrix nano composite (MMNC) at the weld nugget zone (WNZ) of the FSW dissimilar aluminium alloys joint. The bottom-up experimental approach has been successfully adopted for joining two dissimilar aluminium alloys of AA2024-T351 and AA7075-T651 in butt-joint configuration for optimizing the FSW parameters such as tool plunge depth (TPD), tool rotation speed (TRS) and tool travel speed (TTS). Optimized FSW parameters for taper threaded cylindrical tool are TPD, 6.20 mm, TRS, 650 rpm and TTS, 150 mm/min yields higher tensile properties such as ultimate tensile strength (UTS) of 435 MPa, yield strength (YS) of 290 MPa, percentage elongation (% EL) of 13, and maximum weld joint efficiency ( ) of 92% with defect-free microstructures of weld region. Similarly, for taper triangle tool the TPD, 6.20 mm, TRS, 950 rpm and TTS, 90 mm/min yields a higher UTS, 440 MPa, YS, 350 MPa, % EL, 17.5 and of 93% with enhanced microstructure characteristics at the weld region. The tool probe offset of 1 mm towards AA7075-T651 favours the flow characteristics of AA7075-T651 towards WNZ. In addition, increase in the TTS ranging from 20-120 mm/min has revealed higher tensile properties. Higher UTS of 435 MPa, YS of 375 MPa, % EL of 13.6 and of 92% obtained for tool probe offset of 1 mm towards AA7075-T651 and TTS of 110 mm/min with constant TPD of 6.20, and TRS of 650 rpm. For the fabrication ofMMNC at the WNZ produced with varying % vol. fractions (5, 8 and 13) of SiCNP revealed a higher tensile properties of UTS of 418 MPa, YS of 247 MPa and % EL of 14.5 for 5% vol. fraction SiCNP with FSW second pass. The decrease in the grain size range 2-4 µm observed at the WNZ of the MMNC compared to the WNZ without SiCNP having grain size range 6-8 µm. The novelty of this work lies in the demonstration of friction stir welded joint of dissimilar aluminium alloys.
URI: http://idr.nitk.ac.in/jspui/handle/123456789/14565
Appears in Collections:1. Ph.D Theses

Files in This Item:
File Description SizeFormat 
145020ME14P01.pdf14.21 MBAdobe PDFThumbnail
View/Open


Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.